Visit our UK Site
Visit our Asia Site
Description
Product Description
This oil catch tank kit is the product of many months of intensive research and development by our in-house development team, and the end result is by far the most complete oil collection system currently on the market. Not only is it beautifully designed, it has been created to capture the maximum amount of harmful contaminants, including oil deposits, unused fuel vapours and moisture, all of which would ordinarily make their way back through to the inlet of the engine.
Extensive testing has proven our oil catch tank kit's ability to effectively reduce sludge and carbon build up, in turn allowing the Golf Mk5 GTI's TSI engine to both breathe and perform more efficiently. It can therefore be viewed as a genuine performance enhancing product and one we recommend any Mk5 GTI owner seriously consider, particularly if they are planning more advanced power tuning at a later date.
The 0.4l (400cc) catch tank boasts a slew of features intended to make it both easy to check and simple to drain, including a dipstick for level inspection.
The design of the kit has also been carefully considered, hence its inner tube which is constructed from anti-static smooth fuel resistant nitrile rubber. This is paired with an outer cover made from reinforced stainless steel wire braid (a Forge specialty), specifically a partial inner braid and a full cover outer braid. We developed this complex arrangement in order for the tank to be resistant to both pressure expansion and vacuum collapse, and also to enable the kit to function within a clearly defined temperature range – 54°C to +150°C (-65°F to 300°F)
Finally, the kit features a pair of stainless steel reinforced oil resistant hoses with black external braiding, which combine with the supplied fittings to form an OEM-looking product when installed.
Highlights
0.4L capacity*
A dipstick for simple level inspection.
2 Quality stainless steel reinforced oil resistant hoses with black external braiding for that inconspicuous look.
Fully assembled with fittings to suit the OEM connections.
Inner tube is constructed from anti-static smooth fuel resistant nitrile rubber
Outer cover is constructed from reinforced Stainless Steel wire braid consisting of partial inner braid & full cover outer braiding which is resistant to pressure expansion and vacuum collapse
Temperature Range: -54°C to +150°C (-65°F to 300°F)
Installation is straight forward with all necessary fittings and instructions included.
Please note that the engine cover will not fit with this kit without modification
*Dipstick level is set at less than 0.4L for optimum breathing.
Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.
Product Reviews
Product Reviews
Be the first to review this product
Want to leave a review?
Login
Register FREE!
Compatible Vehicles
Instructions
Oil Catch Tank Kit for Golf MK5
Warranty
Warranty Information
The majority of Forge Motorsport products come with a limited lifetime warranty. All warranty claims must be accompanied by the original proof of purchase to enable us to help you — failure to supply this proof will result in your claim or enquiry being denied. Please note that some products are excluded from the Forge lifetime warranty and instead carry their own specific warranty terms — for example, air filters, electrical components, coil packs, carbon fibre products, and suspension kits. This page is a summary only; a full and current list of exclusions, along with their specific warranty terms, can be found on our Terms & Conditions page.
For further information, please call our customer service team on +1 865 951 7456 or email sales@forgemotorsport.com
Do not use aggressive (acidic) car cleaning products, particularly traffic film remover solutions or shampoos, to clean your intercooler, radiator, or oil cooler. The use of these products can damage Forge Motorsport cooling systems and invalidate your warranty. These are often found at car washes. A light, warm, soapy solution (free of harsh acidic cleaning compounds) should be used to clean your cooler, and thoroughly rinsed away afterwards. We recommend that you inspect your product regularly for bent and/or crushed fins — any bent fins should be carefully straightened to allow ambient air to pass through the core face. At the time of installing your Forge radiator, an approved coolant must be used. Be sure you never mix coolant types, and always use distilled water.
This warranty does not apply to any defect in the goods arising from fair wear and tear, wilful damage, accident, negligence by you or any third party, use otherwise than as recommended by the supplier, failure to follow the supplier's instructions, or any alteration or repair carried out without the supplier's approval.
This does not affect your statutory rights.
Ignition Coil Packs
Forge ignition coil packs carry a 12 month warranty against manufacturing defects (not our Lifetime Warranty), from date of purchase. As coil packs are often swapped as a full set on suspicion rather than a confirmed fault, claims must identify the specific faulty unit(s) with supporting evidence (e.g. a diagnostic misfire code) and proof of purchase. Full sets cannot be claimed without this. See full terms and conditions for details.
Electrical Components
Electrical components supplied with Forge Motorsport kits — including solenoids, wiring harnesses and looms — are covered by a 12 month warranty against manufacturing defects, rather than our standard Lifetime Warranty. This covers faulty materials or workmanship only, and does not cover damage from incorrect installation, water ingress, wear, incorrect wiring, or faults originating from your vehicle's own electrical system or other aftermarket electrical accessories. Full terms, including how to make a claim, are available in our Terms & Conditions.
Heat Management Products (Turbo Blankets and Gold Reflective Heat Barrier)
Turbo blankets and our gold reflective heat barrier are covered by a 6 month warranty against manufacturing defects (not our Lifetime Warranty), from date of purchase. Turbo blankets cure and lose flexibility over their first few heat cycles as a normal part of fitting. Once heat-cycled they should not be removed. The gold reflective heat barrier is designed for components such as engine covers, intake pipes and induction trays, not for direct contact with exhausts or turbine housings. See Terms & Conditions for details.
Shipping
Shipping
USA Deliveries
All Deliveries are sent via Fedex. We cannot guarantee delivery timelines as all orders are up to shipper schedules and routes. Delivery fee is a Flat Rate of $20 fo all orders over $20. Orders below that value are costed out based on weight. Signature required may be added to your package. Orders can not be re-directed, held, or re-scheduled.
Shipping outside of the Lower 48- Duty Charge Information
All Forge products are sold with a Delivery Duty Unpaid (DDU) status and an import tariff may apply to your order. Customers will be contacted by the Customs and Excise authority in the destination country regarding payment prior to delivery, and it is important that correct contact telephone number and email information be submitted with the order to facilitate this part of the delivery process.
Our shipping methods ensure safe and timely delivery of your new Forge products. For further information on cost and delivery times, please contact Forge using the info@forgemotorsport.com email address if you require any more information. We reserve the right to change the delivery service and company at any time.
***Once a product has left our warehouse and is in the possession of the shipping company, any claims must be made directly with that shipper however we can assist with most cases.
