We are pleased to present the Forge intercooler for the Veloster N facelift including DCT
*If you use a Veloster N for fast road or have a high performance tune in a hot climate this product is essential*
Utilising our industry leading bar and plate design, alongside Solidworks CAD and flow simulation design (Computational Fluid Dynamics CFD) we developed our high flow cast end tanks. The turbo side endtanks feature an internal divider to ensure the full volume of the stepped core is utilised. The bar and plate core has over 129% more volume and an increase of frontal surface area over 71% (over the stock cooler) meaning the Forge intercooler is the largest currently available on the market. To ensure we deliver optimum cooling efficiency, the development team created a fabricated ducting system that has been skilfully integrated into the superior design of this product this ensures fitment to the inner contour of the Veloster N front bumper.
The inlet and outlet sizes have been increased in diameter to 65mm, giving an increase of 27% more volume over the stock cooler to give perfect flow. The development team also added a custom hard pipe increasing the diameter by 14 mm to 64mm up from the factory 50mm. This replaces the stock factory pipe on the hot side to ensure this package gives you all you need for maximum performance gains on high levels of tune.The boost pipe and intercooler come in our standard black textured finish powder coat for maximum longevity.
Various core designs where tested in the development of the Veloster N intercooler with us finally deciding to use a high-quality Bar and Plate design as used on our highly successful Audi RS3 and TTRS 8s intercoolers resulting in minimal pressure drop.
The results were fantastic with IATS (inlet air temps) being reduced by half and resulting in tremendous gains on tuned vehicles.
During our extensive testing, we let the car heat soak on the dyno until the radiator fans tripped on and off (which gives an inlet temperature of around 40°C). We then did a dyno pull from this point. By doing this, it gives a more consistent result and reflects real-world driving conditions more accurately. You can easily see the Forge intercooler cools much quicker and delivers a much greater drop in temperature compared to OEM.
After more than six pulls on the dyno we still had super safe IATs and the Forge intercooler gave results of 24°C, halving the factory’s intercooler intake temps from 48°C. These tests took place in relatively cold conditions with an ambient dyno cell temperature of 15°C proving how inefficient the stock intercooler is. In the summer months the stock intercooler along with higher inlet air temperatures will have a hugely negative impact on the engine’s performance. In these conditions the engine management will retard the ignition, resulting in a lower powered engine as temperatures rise and the ECU then pulls out the timing to stop detonation. On a mapped vehicle the results will be even more detrimental and can lead to possible premature engine wear.
The Forge Motorsport front mount intercooler has all the necessary hardware to install the kit in approximately 2.5 hours depending on competency and tools available.
Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.
Hyundai Veloster N Facelift Intercooler (Including DCT)
All Forge Motorsport products come with a limited lifetime warranty. All warranty claims must be accompanied by the original proof of purchase to enable us to help you. Failure to supply this proof will result in your claim or enquiry being denied.
For further information, please call our customer service team on +44(0)1452 380999 or email firstname.lastname@example.org.
Do not use aggressive (acidic) car cleaning products, particularly traffic film remover solutions or shampoos to clean your intercooler, radiator or oil cooler. The use of these products can damage Forge Motorsport cooling systems and invalidate your warranty. These are often found at car washes. A light, warm, soapy solution (free of harsh acidic cleaning compounds) should be used to clean you cooler and thoroughly rinsed away. We recommend that you should inspect your product on a regular basis for bent and/or crushed fins. Any bent fins should be carefully straightened to allow ambient air to pass through the core face. At the time of installing your Forge radiator, an approved coolant must be used and added to the coolant system. Be sure you never mix coolant and always use distilled water.
Hyundai i30N/Veloster N/Kona N Dual Catch Can and Expansion Tank
Manufacturer: Forge Motorsport
Blow Off Valve for Ford Focus RS MK3 & Vauxhall Adam, Astra, Corsa, and more
Manufacturer: Forge Motorsport