Description
Product Description
Forge Motorsport are excited to release our industry leading intake for the Hyundai i30N. This aftermarket cold air intake system improves your i30N’s airflow in several key ways. It routes the air more directly into your engine, using a huge 102 mm diameter CNC mandrel bent alloy pipe. The aftermarket system also improves the airflow by adding a high-flow, high efficiency air filter in place of the more restrictive factory air filter. Finally, the cold air intake system is set up to allow cooler air to easily flow into your engine
The intake diameters on these air intakes have been carefully tuned to provide exactly the correct quantity of air ensuring solid consistent power gains throughout the rev range without any loss of low-end torque. The pipework is specifically designed to feed the turbo without interruption. The upshot to all of this is a gain of induction acoustics under acceleration, which improves the driving experience and adds a bit more drama to the Hyundai’s 2.0 four pot engine.
As always filtration is important when developing an intake, so we once again turned to the industry leaders and Forge long term filtration partners Pipercross.
With over 25 years’ experience in both the domestic and motorsport market they recommended a multi-layer foam construction filter, these filters work perfectly in our ‘Hi-Flow’ range. The large filter provided flows 60% more air than the stock filter.
The intake is finished off with our unique black thermal powder coating. This kit comes with Forge’s usual detailed fitting guide to help make installation as easy as possible.
Hyundai boast figures of 275bhp and 278lb.ft on their standard vehicle. When we ran our CAT backed performance exhaust development vehicle on the dyno with this intake it reached figures of 296bhp and 310lb.ft!
Interestingly there has been lots of divided opinions about our intake requiring a heat shield. Testing took place with the bonnet shut and replicated wind speeds of around 70MPH. Intake temperatures were logged and monitored along with thermal images taken,. During this testing, we did not see the inlet pipe or intake temperatures rise; even after 4 hard pulls, the inlet temperatures stayed at a steady 30°C.
Why not add gold tape to the underside of the aluminium housing to further reflect any heat soak from the engine. The Gold tape comes on a 5 metre roll allowing you to apply it to the underside of your Forge Motorsport product.
In the Box:
1 x Black Alloy Hard Pipe
1 x Pipercross Filter
1 x Valve Silicon Joiner
2 x Hose clamps
Please watch our video on how to fit an air filter without damaging it.
Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.
Product Reviews
Product Reviews
Sounds incredible, super easy to install, looks great. Would recommend heat taping it as it gets pretty warm
the sound with this intake system is incredible! this is the way it should sound from the factory!
Absolutely love it! I installed the inlet and the intake at the same time, and the product quality, install process, and results are incredible! Definitely would recommend to anyone looking for an intake system for their veloster N
Works great! Was very easy to install took a little less than an hour. Looks great and sounds great, very solid design. I did some testing with it vs the stock box and the IAT difference is very minimal. In fact at some points the Forge intake was lower. Biggest difference is that heatsoak sets in quicker with the Forge intake but heatsoak dissipates quicker as well so it's a good trade off. Over all I'm very happy with it.
Both graphs had similar ambient temps about 95f 70-80% humidity.
Stock airbox: https://datazap.me/u/jigbits/log-1565486484?log=0&data=1-4-6
Forge intake: https://datazap.me/u/jigbits/log-1565314076?log=0&data=1-4-6
Works great! Was very easy to install took a little less than an hour. Looks great and sounds great, very solid design. I did some testing with it vs the stock box and the IAT difference is very minimal. In fact at some points the Forge intake was lower. Biggest difference is that heatsoak sets in quicker with the Forge intake but heatsoak dissipates quicker as well so it's a good trade off. Over all I'm very happy with it.
Both graphs had similar ambient temps about 95f 70-80% humidity.
Stock airbox: https://datazap.me/u/jigbits/log-1565486484?log=0&data=1-4-6
Forge intake: https://datazap.me/u/jigbits/log-1565314076?log=0&data=1-4-6
Want to leave a review?
Login
Register FREE!
Compatible Vehicles
Instructions
Induction Kit for Hyundai i30N, Kona N, Veloster N, and Elantra N
Warranty
Warranty Infomation
All Forge Motorsport products come with a limited lifetime warranty. All warranty claims must be accompanied by the original proof of purchase to enable us to help you. Failure to supply this proof will result in your claim or enquiry being denied.
For further information, please call our customer service team on +44(0)1452 380999 or email info@forgemotorsport.co.uk.
Do not use aggressive (acidic) car cleaning products, particularly traffic film remover solutions or shampoos to clean your intercooler, radiator or oil cooler. The use of these products can damage Forge Motorsport cooling systems and invalidate your warranty. These are often found at car washes. A light, warm, soapy solution (free of harsh acidic cleaning compounds) should be used to clean you cooler and thoroughly rinsed away. We recommend that you should inspect your product on a regular basis for bent and/or crushed fins. Any bent fins should be carefully straightened to allow ambient air to pass through the core face. At the time of installing your Forge radiator, an approved coolant must be used and added to the coolant system. Be sure you never mix coolant and always use distilled water.
Shipping
Shipping
USA Deliveries
All Deliveries are sent via Fedex. We cannot guarantee delivery timelines as all orders are up to shipper schedules and routes. Delivery fee is a Flat Rate of $20 fo all orders over $20. Orders below that value are costed out based on weight. Signature required may be added to your package. Orders can not be re-directed, held, or re-scheduled.
Shipping outside of the Lower 48- Duty Charge Information
All Forge products are sold with a Delivery Duty Unpaid (DDU) status and an import tariff may apply to your order. Customers will be contacted by the Customs and Excise authority in the destination country regarding payment prior to delivery, and it is important that correct contact telephone number and email information be submitted with the order to facilitate this part of the delivery process.
Our shipping methods ensure safe and timely delivery of your new Forge products. For further information on cost and delivery times, please contact Forge using the info@forgemotorsport.com email address if you require any more information. We reserve the right to change the delivery service and company at any time.
***Once a product has left our warehouse and is in the possession of the shipping company, any claims must be made directly with that shipper however we can assist with most cases.